Glass looks clean for about a day. Then hard-water spots dry on the shower screen, rain leaves streaks on the windows and soap scum builds up on bathroom tiles. Most of the work of cleaning glass is fighting what dries and sticks to it.
A nano glass coating makes that work much lighter. This guide explains how it works on shower screens, windows and glazed ceramics, what it can and cannot fix, and how to apply and maintain it.
Key takeaways
- A nano glass coating makes water bead and run off, carrying loose dirt with it.
- Limescale and soap scum find it harder to stick, so a rinse and squeegee replaces scrubbing.
- It cannot repair glass that is already etched, scratched or chipped.
- Expect up to 5 years on exterior glass and 6 to 12 months in a shower in daily use.
How a nano glass coating works
The coating carries silica (SiO₂) building blocks a few billionths of a metre across. As the carrier evaporates they react with the glass and with each other, forming a glass-like film far thinner than a soap bubble, with water-repelling groups facing outwards. Water beads up instead of spreading into a sheet, so dirt and minerals have less to grip and rinse away more easily.
Where it helps most
| Surface | What changes |
|---|---|
| Shower screens and bathroom glass | Water runs off; fewer hard-water spots; squeegee in seconds |
| Windows, glass doors and balustrades | Rain beads and runs off; streaks and grime build up more slowly |
| Glazed tiles, basins, baths and toilets | Soap scum and limescale struggle to stick |
| Shopfronts, façades and skylights | Longer intervals between cleans |
| Pool fences and glass railings | Splash marks rinse away |
What it cannot do
- It does not repair glass that is already etched, scratched or chipped. Restore heavily scaled or etched glass first, or replace it.
- It does not stop glass cracking or breaking. It is an easy-clean finish, not armour.
- It is not for unglazed tiles, natural stone or grout. Use Stone + Brick for those.
- Test first on window tint films and coated low-E glass. It is not for acrylic or polycarbonate.
Hard water and Indian homes
In many Indian cities tap water carries a lot of dissolved minerals. When droplets dry on glass they leave white spots that bond to the surface over time. On coated glass more of the water runs off before it dries, so fewer spots form, and those that do wipe off more easily. In showers, a quick squeegee after use keeps the glass clear for longer.
How it is applied
- Clean thoroughly. Remove grease, limescale, old polishes and sealers; the coating bonds to the glass, not to dirt.
- Finish with an isopropyl alcohol (IPA) wipe and let the surface dry completely.
- Work in the shade between 5 and 35 °C, below 85% relative humidity, with no rain expected for 12 hours.
- Spray lightly onto about 1 m² at a time, or onto the applicator cloth, and wipe in overlapping circles.
- After 2 to 5 minutes, buff off any haze with a clean, dry microfibre cloth.
- Keep dry and untouched for 1 hour. Full water repellency develops within 24 hours.
Glass + Ceramic is supplied as a two-part unit (Part A + Part B), diluted with ethanol or IPA on site. One unit makes 20 litres of coating and covers 18,000 to 20,000 sq ft. Once diluted it is highly flammable, so mix and apply away from heat and flames, with good ventilation.
Care and re-application
- Rinse with water and wipe with a soft microfibre cloth; use a mild, pH-neutral detergent when needed.
- Avoid abrasive pads, scouring powders and strongly alkaline cleaners such as bleach; they wear the coating away.
- In hard-water areas, a mild acidic cleaner now and then removes mineral build-up.
- When water stops beading, clean with an IPA wipe and re-apply.
Frequently asked questions
Is a nano glass coating worth it for a shower screen?
For most homes, yes. Water runs off, limescale and soap scum build up more slowly, and cleaning becomes a rinse and squeegee. In a shower used daily, expect to re-apply every 6 to 12 months.
Will it remove existing hard-water stains?
No. Remove existing stains and scale before applying. The coating then slows new build-up.
Can I use it on mirrors and windows?
Yes: mirrors, windows, glass doors, balustrades and skylights, as well as glazed tiles and sanitaryware.
Does it change how the glass looks?
No. The film is far thinner than the wavelength of light, so it is invisible once buffed.
Coating glass on a project or across properties? One unit covers 18,000 to 20,000 sq ft. Tell us the surfaces and area.
